Adding R-Pod 179 slide out window |
Post Reply |
Author | |
john_benham
Groupie Joined: 31 May 2015 Location: Spokane Status: Offline Points: 44 |
Post Options
Thanks(0)
Posted: 16 Jul 2018 at 12:30pm |
Wil,
Looks like you did a really good job. So far my installation has caused no structural issues. I'm amazed on how much extra view it adds plus the benefit of the closet window. Personally I think it will add to the resale value of our R-Pods. Off for another R-Pod adventure. Hired to record and do sound for the montana Baroque Festival at Quinn's Hot Springs. R-Pod really packed with gear. It's only going to be 97F there today!! Thanks for sharing. Later, John B.
|
|
wthoms2000
Newbie Joined: 08 Nov 2017 Location: Orange County C Status: Offline Points: 1 |
Post Options
Thanks(0)
|
John, finally put a window on my 179 slider! Thank you for the accurate info and motivation.
|
|
Porta Poddy
Wil Thoms 2017 179 HRE Orange County CA |
|
john_benham
Groupie Joined: 31 May 2015 Location: Spokane Status: Offline Points: 44 |
Post Options
Thanks(0)
|
R-Pods definitely need a window in the dinette area.
Cutout: 14 1/4" wide x 21 1/4" high x 1 1/4" thick. The aluminum rectangular channel is towards the top of the cutout. It is 2 1/2" x 1". I think its only purpose is to add a little structural strength but the ratcheted bars that pull in and out the slide-out supply that. There was no wiring going through which was my main concern. We've had ours since 2015 and have had no issues with this modification. The window came with inside window frame self tapping screws which I assumed were long enough. They weren't. I had already siliconed the outside window portion then was going to screw in the inner frame and found the small screw thing out!. Had to stop, buy the correct length screws and drill a pilot hole to make sure it all fit together. That was the only issue with my installation. So best dry fit everything, then silicone a seal and install. Attached is a photo of the cutout if that helps. Good luck. John B. Spokane |
|
gertter
Newbie Joined: 04 Jan 2018 Location: McCall, ID Status: Offline Points: 1 |
Post Options
Thanks(0)
|
I'm hoping to add windows to my 179 slide out as well. Was the aluminum channel near the bottom of the cut, or the top? I'm thing I want to put a smaller window in just above the aluminum channel if possible. How thick were the walls?
Good job on you Pod-Mod! Thanks!
|
|
furpod
Senior Member Joined: 24 Jul 2011 Location: Kentucky Status: Offline Points: 966 |
Post Options
Thanks(0)
|
It isn't. Only one pod uses this size slide. There are no appliances in the slide. |
|
john_benham
Groupie Joined: 31 May 2015 Location: Spokane Status: Offline Points: 44 |
Post Options
Thanks(0)
|
It might simply be a corridor for wiring with the wall used in other model applications. But, as you say, time will tell!
Thanks.
|
|
furpod
Senior Member Joined: 24 Jul 2011 Location: Kentucky Status: Offline Points: 966 |
Post Options
Thanks(0)
|
I wouldn't like the idea of cutting out a large chunk of the framing, but time will tell if it's an issue. It certainly looks good, and I am sure it makes it feel more open..
|
|
john_benham
Groupie Joined: 31 May 2015 Location: Spokane Status: Offline Points: 44 |
Post Options
Thanks(0)
|
R-Poders,
The first item I noticed with our R-Pod 179 was lack of peripheral window view in the dinette slide out. I measured the side wall and found a 21" x 14" window that would match and be suitable. It is from www.Teardroptrailerparts.com - window WD06. It arrived quickly and came with an internal finish frame and mounting screws. My installation took longer than I thought. Hopefully after sharing my issues, it will only take about an hour or so. _________________________________________________________________________ Make a template from cardboard and trace it where you want it on the inside wall. It is a 14 1/4" x 21 3/4" cutout with 4" corner radii. Drill an 3/8" jigsaw start hole just on the inside of your template mark. Then center and place the template on the outside wall and use a Sharpy marker, trace the cutout. The wall is 1-11/16" thick. I put masking tape on the jigsaw bottom plate as to not scratch the finish. Use the jigsaw with a medium fine blade to cut out the opening. About 2/3rds the way up on my opening, I ran into an aluminum channel I assumed used for additional wall strength. You can see it on the cut out wall section photo. I changed jigsaw blades to a metal blade and easily cut through the aluminum. (Ask me in a year if the slide out has collapsed or not...) Putting in the window should add some strength to the wall, so I'm not that worried. The screws that came with the window are not long enough. You need 15 8x3/4" black capped window screws. Pre-drill the finish frame screw holes on the window frame using a 5/32" drill. It's hard, but try to center all holes the best you can. Clean the outside portion of the opening with acetone before fitting the window. Put a seam of good silicone sealant on the rubber window seal and place the window into its opening - best to have an extra person to hold it from the outside. From the inside, screw the finish frame onto the window using the 8x3/4" screws. I would cover the outside portion of the inside finish frame with masking tape to protect the finish from drill burnishing. (I have to paint a few blemishes on mine!) 15 screws later one is finished. After the silicone set, I cleaned up any extra on the outside with a razor blade and acetone. Issues I had: I assumed the screws that came with the window worked - no. Only after I put silicone on the seal I found this out. And I tried doing it by myself. Best to have someone on the outside to hold the window in place while you are securing it. Cut the window opening from the outside. I tried from the inside and it was hard to see and cut a perfectly straight cut out line. Once I hit the aluminum channel bar, it was too late to back out of this project!! You have to drill pilot holes into the window frame for the correct screws and make sure they are centered as well as you can make them. Hope your window addition goes faster and smoother with what I've learned. _____________________________________________________________ From the photos, you can see the view is now fabulous! Enjoy! John Spokane, WA |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |